Rock Drilling Things To Know Before You Buy

Generally called DTH, the Down-the-Hole Hammer drill is a percussive gadget in round type with indispensable drill bit that is fitted straight onto the bottom of a drill string. DTH is among one of the most effective means of drilling rock, utilizing a rapid hammer action to damage the rock into considerable chips which are then evacuated from the birthed hole by the air worn down from the DTH Hammer. The strategy offers fast boring of accurately straightened, directly and also tidy holes in most ground problems.

It is necessary to keep in mind in rock extraction that blowing up is the very first stage of squashing. It is as a result crucial that time as well as effort is invested in making sure that the hole dimension, general blast style as well as explosive loading is appropriate for the conditions, in order to accomplish excellent fragmentation, optimum productivity, risk-free secure faces and degree floorings at minimal expense.

DTH is a reasonably recent method, presented in the 1950s when the selection of drilling system for quarrying was limited, that after that included the hand-held jack hammer, cable television device, and also rotary drill as well as the air-driven leading hammer machines.

Jack hammers were used for springing, quiting and also popping. Although they were lightweight, mobile, easily kept and low-cost, they were basically labour intensive, reduced quantity producers, leading to little openings and restricted control, in addition to offering significant health and safety problems.

The wire tool was primitive and utilized a hefty bar with a carve, suspended on a cable rope that was after that mechanically went down on the rock to crush it within the hole, using water to bale clear the resultant cuttings as well as dirt. Once more easy to use, simple to preserve with inexpensive procedure, minimal dust as well as efficient in bad ground, yet the cable tool was sluggish as well as minimal to bigger holes, without any positioning control. It called for a normal water supply, two guy procedure and also was really only of use for soft to medium rock developments.

Rotating exploration required large, heavy gears to develop weight behind the drill little bit and provide quick rotational rates with high torque capacities to pass through the rock. Although they were relatively quick, economical to run as well as keep and also good in poor ground, they needed a high capital outlay, were prone to hole variance and also offered much less impressive performance in hard rock.

The Leading Hammer drill or drifter was a mechanical variation of the hand-held jack hammer with the air driven percussive device pole mounted on a simple three wheeled carriage. It was quick, mobile, very easy to keep and also good in hard rock. However, it went through hole variance, minimized exploration rate at deepness and produced high noise levels as well as resonance. Opening dimensions were limited to 70 to 100mm sizes.

Back in the 1950s, rock filling methods were sometimes primitive, using rope excavators or hand loading into railway tubs. Furthermore, high upright faces paired with inadequate control over blowing up raised the threat of rock falls resulting in injury and death.

Against this background, the innovative DTH boring method showed up on the scene in the very early part of that years, created by Belgian marble quarry proprietor Andre Stenuick. Its several benefits were promptly evident:-.

Suitable for all types of rock (except clay).
Greater versatility in terms of hole sizes.
Low capital outlay.
Easy as well as very easy to operate.
For blast hole drilling DTH meant straighter, cleaner, better aligned holes for simpler charging, improved blasting control, improved faces, better floors, improved fragmentation and throughput as well as lower operating costs. Possibly most considerably, DTH implied greater overall safety.

By the 1970s, DTH Hammers were typically working at 10 bar. With the system well established in blast hole operations, potential also extended within the water well drilling sector. Benefits consisted of reduced capital outlay, all rock capacity with a bigger series of opening dimensions feasible utilizing the exact same hammer, deep hole ability, simpler insertion of linings, screens and pumps and in particular tidy openings for cleaner water were conveniently recognizable.

So in 2012, where are the various other systems? Today's Leading Hammer makers are hydraulically run with taxis as well as full automation, offering high energy output and productivity. They are ideal for short, small diameter holes in hard consolidated formations, but less effective in softer, broken ground. With deviation still a risk on deep holes, they can be also extremely noisy unless soundproofed. Requiring a high capital outlay and sometimes with high cost consumables but low fuel usage, they are versatile and maneuverable and can be highly productive on short hole drilling applications but because of the high penetration and restricted air flow, the risk of rifling (spiralling in the hole) and dust left in the bottom of holes can be a problem.

Rotary drills are now commonly used in big, open pit mines, producing larger holes from 165-300mm diameter, usually for short hole, multi row blasting in medium/soft rock. Steel tooth tricone bits are used in softer rock, with tungsten carbide types for harder rock. Internal bearings in tri-cone bits restrict the minimum hole size to 152mm, so rotary drag bits are normally used for drilling holes below 152mm but mainly in soft rock. The rotary drilling principle is still widely used in deep-hole water well drilling and for oil and gas wells.

Cable Tool machines are still used in drilling for water in under-developed countries, whilst the original hand-held jack hammer principle has thankfully been consigned to the past.

In contrast, DTH goes from strength to strength. More effective button bits were introduced in the late sixties, providing better cutting action, faster and smoother drilling, greater accuracy, longer life with less regrinding (if any), therefore increasing productivity and reducing drilling costs. A variety of head design and tungsten inserts became available to suit different formations and drilling conditions.

Today's valveless DTH hammers are simpler, faster and more effective, especially at the higher air pressures of 25 to 40 bar. When drilling with higher air pressure, penetration rates increase pro-rata to increases in pressure, giving greater productivity at less cost per metre drilled.

Now fully automated, today's DTH blast-hole machines are designed for safe, all weather operation, having air conditioned, soundproofed cabs with multi angle drilling capabilities, on-board compressors, dust collectors, angle indicators, computer logging facilities and track mounted for engaging all ground conditions. In short, they still provide the industry with straight, clean, accurately aligned holes for easy charging, greater blast control, good fragmentation, safer faces and better floors, combined with excellent levels of productivity and attractive overall cost advantages.

Having started out as a blast-hole system, applications now using DTH include water well drilling, geo-thermal drilling piling, ground consolidation, mineral exploration, shallow oil and gas, post hole insertion, directional drilling and even mine rescue - it was through the use of the DTH system that the trapped Chilean miners were successfully located and provided with vital water, food, medications and communications until a full rescue was made.

DTH Hammers have precision parts manufactured to fine tolerances, requiring some basic care to maintain the best results. Users should adhere to manufacturers' recommendations, preventing dirt from entering the hammer and using the correct rock oil in the right amounts to suit ambient and ground conditions. Regular checks should be made of the outer case of the hammer for any sign of damage; it pays to periodically strip and inspect the internal parts of the hammer for signs of wear or damage and replace any such items. In abrasive conditions the outer case of the hammer may wear more quickly than the inner components and if properly cared for, these internal items can be used to re-build the hammer using an outer case re-build kit to prolong its life. This can often be carried out two or three times without any detrimental effect on the performance of the hammer in service. When not in use, the hammers should be oiled up and stored horizontally in a dry place and before returning to service, a quantity of oil should be poured into the hammer to ensure that internal parts are well lubricated.

Reputable makes of drill bit should always be selected that are truly compatible with the hammer; these should be regularly checked in service to make sure the body is in good condition and not worn - the splines of the bit (and of the chuck) should be lubricated by the oil from the hammer to ensure that wear is kept to a minimum. Plastic foot-valves should be checked to make sure that they are not loose or in any way worn or damaged and should be replaced if any such damage is observed. Drill bits should be protected during storage and handling to prevent damage to the tungsten carbide inserts and the plastic foot vales.

The DTH Hammer method provides one of the most efficient and versatile ways of drilling in a wide variety of rock conditions for many different applications. It provides fast penetration even in the hardest rock with constant speed throughout the length of the bore hole with the added benefits of accuracy and alignment to give good clean usable holes. DTH does not rely on heavy machines with fast rotational speeds or heavy down-thrusts; it only requires that the hammer be subjected to sufficient thrust to initiate the percussive operation and that there is the appropriate amount of rotational speed, usually around 28 to 40rpm, to relocate the drill bit on the rock face to produce the optimum size of cutting and minimal dust production. Performance, reliability, minimal spares usage, long service life and overall cost effectiveness are the hallmarks of a well-designed and manufactured 'World Class' DTH hammer that brings benefits to both the driller and the operating company - it is important to go for quality and not price when making the choice to purchase your DTH hammer.Learn more about Foundation Drilling here.

Leave a Reply

Your email address will not be published. Required fields are marked *